labsnanax.blogg.se - february 2022

Backup exec 2010 tapes license key#
Backup exec 2010 tapes software#
Backup exec 2010 tapes trial#
Backup exec 2010 tapes windows#

just run the clean tape 3/4 times and now my backup works again. Isolate the tape drive on its own controller card. Check/replace the SCSI cable or terminator.ħ. Disable the sync negotiation to the tape device in the SCSI setup program.Ħ. Use the manufacturer's SCSI setup program to lower the transfer rate.ĥ. SCSI transfer rate to the tape device is too fast. This would require replacing the tape device.Ĥ. Running 3-4 consecutive cleaning cycles will usually resolve this problem.ģ.

Backup exec 2010 tapes trial#

If no License Numbers are entered, Backup Exec will be installed in a 60-day Trial Mode. (Figure 6) Note: Repeat step 7 as often as necessary in order to add more Licenses for additional Backup Exec Agents & Options.

Backup exec 2010 tapes license key#

Enter a valid Backup Exec 2010 Product License Key and select Add. Review the summary and Click Next to continue. (Figure 5) (See Related Documents section) Figure 5: 8. Contaminated read/write heads of the tape device. Backup Exec Installation will run the Environment Check. The following list contains the most common reasons for this error and potential solutions:ġ. The "Bad Data" error is generic in nature and can be caused by many factors. The error message "Bad Data" is reported by Backup Exec during backup or verify operations.īackup Exec reported an error on a request to (read/write) data (to/from) storage media.

Backup exec 2010 tapes software#

I used Quantum Software to verify my backupunit (HP VS80) and all was ok.īut I still received the same error message. I used a cleaning tape to clean the heads. The above message I got 2 consequitve times from backup exec. This could be caused by either a dirty tape drive, bad media, or a SCSI problem. Error reported: Data error (cyclic redundancy check). Storage device "HP 1" reported an error on a request to read data from media. Management feature also manages the backup data on the disk storage device.Job ended: dinsdag 15 januari 2008 at 0:35:07įinal error: 0xe00084c7 - The media is bad.įinal error category: Backup Media Errorsįor additional information regarding this error refer to link V-79-57344-33991 We put the latest Backup Exec 2010 to the test to see what.

Backup exec 2010 tapes windows#

When a legacy backup-to-diskįolder becomes empty, Backup Exec deletes it. Symantec Backup Exec 2010 review It’s been a long wait but Symantec finally adds deduplication to its flagship Windows backup software. Backup Exec’s data lifecycle management feature manages theĮxisting data in the legacy backup-to-disk folders, eventually expiring andĭeleting the data according to the overwrite protection period that you All backup jobs that were sent to the legacy backup-to-diskįolders are now sent to the disk storage device that Backup Exec 2012 creates BackupĮxec no longer creates new backup sets in the legacy backup-to-diskįolders. The read-onlyīackup-to-disk folders are called legacy backup-to-disk folders. Read-only so that the data can be restored from them. All of the other backup-to-disk folders on the volume become Storage is a location on a locally attached internal hard drive, a USB device,Ī FireWire device, or a network-attached storage device to which you can back

Alternately, a notification can be sent via text message as well by checking the Send notifications by text message box and entering in the phone number of the deviceīackup-to-disk folders are on the same volume, Backup Exec 2012 converts oneīackup-to-disk folder on the volume to a disk storage device.

Check the Send notifications by Email box and then enter in the Recipient's email address (i.e.

In the next window that opens, enter in the user name of the person to send the notification to in the Name: field.

Enter in the Email address of the sender in the Sender Email address: field ( Click OK.

Enter in the name of the sender in the Sender Name: field.

Under Email Server: Type the name of the exchange server.

Click add a recipient, Click yes if a configuration pop up box appears.

Select C onfigurations and Settings > Alerts and Notifications > Recipient configurations.